View SFF7N60_1307523.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SemiWell Semiconductor
SFF7N60
N-Channel MOSFET
Features

RDS(on) (Max 1.2 )@VGS=10V Gate Charge (Typical 28nC) Improved dv/dt Capability, High Ruggedness 100% Avalanche Tested Maximum Junction Temperature Range (150C)
Symbol
2. Drain
1. Gate

3. Source
General Description
This Power MOSFET is produced using Semiwell's advanced planar stripe, DMOS technology. This latest technology has been especially designed to minimize on-state resistance, have a high rugged avalanche characteristics. These devices are well suited for high efficiency switch mode power supplies, active power factor correction, electronic lamp ballasts based on half bridge topology.
TO-220F
1
2
3
Absolute Maximum Ratings
Symbol
VDSS ID IDM VGS EAS EAR dv/dt PD TSTG, TJ TL Drain to Source Voltage
(* Drain current limited by junction temperature)
Parameter
Continuous Drain Current(@TC = 25C) Continuous Drain Current(@TC = 100C) Drain Current Pulsed Gate to Source Voltage Single Pulsed Avalanche Energy Repetitive Avalanche Energy Peak Diode Recovery dv/dt Total Power Dissipation(@TC = 25 C) Derating Factor above 25 C Operating Junction Temperature & Storage Temperature Maximum Lead Temperature for soldering purpose, 1/8 from Case for 5 seconds.
(Note 2) (Note 1) (Note 3) (Note 1)
Value
600 7.0* 4.4* 28*
Units
V A A A V mJ mJ V/ns W W/C C C
30
420 14.7 4.5 48 0.38 - 55 ~ 150 300
Thermal Characteristics
Symbol
RJC RJA
Parameter
Thermal Resistance, Junction-to-Case Thermal Resistance, Junction-to-Ambient
Value Min.
-
Typ.
-
Max.
2.6 62.5
Units
C/W C/W
Copyright@Semiwell Semiconductor Inc., All rights reserved.
SFF7N60
Electrical Characteristics
Symbol Off Characteristics
BVDSS BVDSS/ TJ IDSS Drain-Source Breakdown Voltage Breakdown Voltage Temperature coefficient Drain-Source Leakage Current Gate-Source Leakage, Forward Gate-source Leakage, Reverse VGS = 0V, ID = 250uA ID = 250uA, referenced to 25 C VDS = 600V, VGS = 0V VDS = 480V, TC = 125 C VGS = 30V, VDS = 0V VGS = -30V, VDS = 0V VDS = VGS, ID = 250uA VGS =10 V, ID = 3.5A 600 0.6 10 100 100 -100 V V/C uA uA nA nA ( TC = 25 C unless otherwise noted )
Parameter
Test Conditions
Min
Typ
Max
Units
IGSS
On Characteristics
VGS(th) RDS(ON) Gate Threshold Voltage Static Drain-Source On-state Resistance 2.0 1.0 4.0 1.2 V
Dynamic Characteristics
Ciss Coss Crss td(on) tr td(off) tf Qg Qgs Qgd Input Capacitance Output Capacitance Reverse Transfer Capacitance VGS =0 V, VDS =25V, f = 1MHz 1100 110 12 1500 150 16 pF
Dynamic Characteristics
Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Total Gate Charge Gate-Source Charge Gate-Drain Charge(Miller Charge) VDS =480V, VGS =10V, ID =7.0A
(Note 4, 5)
VDD =300V, ID =7.0A, RG =25
(Note 4, 5)
15 30 110 40 28 5 11
40 70 230 90 37 nC ns
-
Source-Drain Diode Ratings and Characteristics
Symbol
IS ISM VSD trr Qrr NOTES
1. Repeativity rating : pulse width limited by junction temperature 2. L = 15.7mH, IAS =7A, VDD = 50V, RG = 25 , Starting TJ = 25C 3. ISD 7A, di/dt 200A/us, VDD BVDSS, Starting TJ = 25C 4. Pulse Test : Pulse Width 300us, Duty Cycle 2% 5. Essentially independent of operating temperature.
Parameter
Continuous Source Current Pulsed Source Current Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge
Test Conditions
Integral Reverse p-n Junction Diode in the MOSFET IS =7.0A, VGS =0V IS=7.0A, VGS=0V, dIF/dt=100A/us
Min.
-
Typ.
365 3.4
Max.
7.0 28 1.4 -
Unit.
A V ns uC
Copyright@Semiwell Semiconductor Inc., All rights reserved.
Typical Characteristics
10
1
ID, Drain Current [A]
ID, Drain Current [A]
VGS 15.0 V 10.0 V 8.0 V 7.0 V 6.5 V 6.0 V 5.5 V Bottom : 5.0 V Top :
10
1
150 C
10
0
o
10
0
25 C -55 C
o
o
10
-1
Notes : 1. 250s Pulse Test 2. TC = 25
Notes : 1. VDS = 40V 2. 250s Pulse Test
10
-1
10
0
10
1
10
-1
2
4
6
8
10
VDS, Drain-Source Voltage [V]
VGS, Gate-Source Voltage [V]
Figure 1. On-Region Characteristics
Figure 2. Transfer Characteristics
5
RDS(ON) [ ], Drain-Source On-Resistance
VGS = 10V
3
VGS = 20V
IDR, Reverse Drain Current [A]
4
10
1
2
10
0
150
25
Notes : 1. VGS = 0V 2. 250s Pulse Test
1
Note : TJ = 25
0
0
5
10
15
20
25
10
-1
0.2
0.4
0.6
0.8
1.0
1.2
1.4
ID, Drain Current [A]
VSD, Source-Drain voltage [V]
Figure 3. On-Resistance Variation vs Drain Current and Gate Voltage
Figure 4. Body Diode Forward Voltage Variation with Source Current and Temperature
2000
Ciss = Cgs + Cgd (Cds = shorted) Coss = Cds + Cgd Crss = Cgd
12
VGS, Gate-Source Voltage [V]
10
VDS = 120V VDS = 300V
1500
Capacitance [pF]
Ciss
8
VDS = 480V
1000
Coss
6
4
500
Crss
Notes : 1. VGS = 0 V 2. f = 1 MHz
2
Note : ID = 7.0 A
0 -1 10
0
10
0
10
1
0
5
10
15
20
25
30
35
VDS, Drain-Source Voltage [V]
QG, Total Gate Charge [nC]
Figure 5. Capacitance Characteristics
Figure 6. Gate Charge Characteristics
Typical Characteristics
(Continued)
1.2
3.0
BVDSS, (Normalized) Drain-Source Breakdown Voltage
1.1
RDS(ON), (Normalized) Drain-Source On-Resistance
2.5
2.0
1.0
1.5
1.0
0.9
Notes : 1. VGS = 0 V 2. ID = 250 A
0.5
Notes : 1. VGS = 10 V 2. ID = 3.5 A
0.8 -100
-50
0
50
100
o
150
200
0.0 -100
-50
0
50
100
o
150
200
TJ, Junction Temperature [ C]
TJ, Junction Temperature [ C]
Figure 7. Breakdown Voltage Variation vs Temperature
Figure 8. On-Resistance Variation vs Temperature
8
10
2
Operation in This Area is Limited by R DS(on)
ID, Drain Current [A]
10
1
10 ms DC
10
0
10
-1
Notes : o 1. TC = 25 C o 2. TJ = 150 C 3. Single Pulse
0
10
-2
ID, Drain Current [A]
10 100 s s 1 ms
6
4
2
10
10
1
10
2
10
3
0 25
50
75
100
125
150
VDS, Drain-Source Voltage [V]
TC, Case Temperature []
Figure 9. Maximum Safe Operating Area
Figure 10. Maximum Drain Current vs Case Temperature
10
0
Z JC(t), Thermal Response
D = 0 .5 0 .2
10
-1
N o te s : 1 . Z J C (t) = 0 .8 5 /W M a x . 2 . D u ty F a c to r, D = t 1 /t 2 3 . T J M - T C = P D M * Z J C (t)
0 .1 0 .0 5 0 .0 2 0 .0 1 s in g le p u ls e
PDM t1 t2
10
-2
10
-5
10
-4
10
-3
10
-2
10
-1
10
0
10
1
t 1 , S q u a re W a v e P u ls e D u ra tio n [s e c ]
Figure 11. Transient Thermal Response Curve
Gate Charge Test Circuit & Waveform
5K 0 1V 2 20F 0n 30F 0n
Sm Tp a e ye a DT sU VS D
VS G Q g 1V 0 Q g s Q g d
VS G
DT U
3A m
Cag hr e
Resistive Switching Test Circuit & Waveforms
V D S R G V G S
R L V D D
V D S
9 0 %
1 0 V
D U T
V G S
1 0 %
t(n d) o
t r tn o
t(f) df o tf o f
t f
Unclamped Inductive Switching Test Circuit & Waveforms
L V D S I D R G 1 0 V
tp
BS VS D 1 - I 2 ---------E =-- L S ---------AS A 2 B S -V VS D D D BS VS D IS A V D D I( t D) V D D
tp
D U T
V () Dt S Te i m
Peak Diode Recovery dv/dt Test Circuit & Waveforms
DUT
+ V
DS
_ I
SD
L D r iv e r R
G
S am e T ype as DUT
V
DD
V
GS
* d v / d t c o n t r o lle d b y R G * I S D c o n t r o lle d b y p u ls e p e r io d
V GS ( D r iv e r )
G a t e P u ls e W id t h D = -------------------------G a t e P u ls e P e r io d
10V
I F M , B o d y D io d e F o r w a r d C u r r e n t
I SD (DUT ) IR M
d i/d t
B o d y D io d e R e v e r s e C u r r e n t
V DS (DUT )
B o d y D io d e R e c o v e r y d v / d t
V
SD
V
DD
B o d y D io d e F o r w a r d V o lt a g e D r o p
Package Dimensions
TO-220F
3.30 0.10 10.16 0.20 (7.00) o3.18 0.10 2.54 0.20 (0.70)
6.68 0.20
15.80 0.20
(1.00x45)
9.75 0.30
MAX1.47 0.80 0.10
(3 0 )
0.35 0.10 2.54TYP [2.54 0.20]
#1 0.50 -0.05 2.54TYP [2.54 0.20] 4.70 0.20
+0.10
2.76 0.20
9.40 0.20
15.87 0.20

▲Up To Search▲

Price & Availability of SFF7N60

	To Download SFF7N60 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .